s p o n s o r e d   l i n k s

engineering ebook

The Citroën Technical Guide.pdf

November 18, 2009 · Filed Under Citroen · Comment  · Tags:

Taken from Diesel engines: Diesel oil has been a contender to gasoline for many decades. Earlier diesel engines were not refined enough to win the hearts of many drivers but recent advances in technology made these engines not only a worthy competitor in all areas but in some features—fuel economy or low end torque, to name just two—even exceeding the characteristics of their gasoline counterparts. And in addition to the general technological advantages, Citroën’s diesel engines have a widely accepted reputation—even among people blaming the quirkiness of its suspension or other features of being excellent and robust.

s p o n s o r e d   l i n k s


Basics of Fluid Mechanics.pdf

November 16, 2009 · Filed Under Mechanical & Industrial Engineering · Comment  · Tags: ,

Taken from: What is Fluid Mechanics?: The fluid mechanics study involve many fields that have no clear boundary between them. Researchers distinguish between orderly flow and chaotic flow as the laminar flow and the turbulent flow. The fluid mechanics can also be distinguish between a single phase flow and multiphase flow (flow made more than one phase or single distinguishable material). The last boundary (as all the boundaries in fluid mechanics) isn’t sharp because fluid can go through a phase change (condensation or evaporation) in the middle or during the flow and switch from a single phase flow to a multi phase flow. Moreover, flow with two phases (or materials) can be treated as a single phase (for example, air with dust particle).

Fundamentals of Compressible Flow Mechanics.pdf

November 9, 2009 · Filed Under Mechanical & Industrial Engineering · Comment  · Tags: , ,

Taken from Preface: This book, Fundamentals of Compressible Flow, describes the fundamentals of compressible flow phenomena for engineers and others. This book is designed to replace the book(s) or instructor’s notes for the compressible flow in (mostly) undergraduate classes for engineering/science students. It is hoped that the book could be used as a reference book for people who have at least some knowledge of the basics of fundamental fluid mechanics, and basic science such as calculus, physics, etc. It is hoped that the computer program enclosed in the book will take on a life of its own and develop into an open content or source project.
The structure of this book is such that many of the chapters could be usable independently. For example, if you need information about, say, Fanno flow, you can read just chapter 9. I hope this makes the book easier to use as a reference manual. However, this manuscript is first and foremost a textbook, and secondly a reference manual only as a lucky coincidence.

Automating Manufacturing Systems with PLCs.pdf

November 9, 2009 · Filed Under Mechanical & Industrial Engineering · Comment  · Tags: , , ,

Taken from PROGRAMMABLE LOGIC CONTROLLERS’s Introduction: Control engineering has evolved over time. In the past humans were the main method for controlling a system. More recently electricity has been used for control and early electrical control was based on relays. These relays allow power to be switched on and off without a mechanical switch. It is common to use relays to make simple logical control decisions. The development of low cost computer has brought the most recent revolution, the Programmable Logic Controller (PLC). The advent of the PLC began in the 1970s, and has become the most common choice for manufacturing controls.
PLCs have been gaining popularity on the factory floor and will probably remain predominant for some time to come. Most of this is because of the advantages they offer: Cost effective for controlling complex systems.
Flexible and can be reapplied to control other systems quickly and easily.
Computational abilities allow more sophisticated control.
Trouble shooting aids make programming easier and reduce downtime.
Reliable components make these likely to operate for years before failure.

A PLC Primer.pdf

November 8, 2009 · Filed Under Electrical Engineering · Comment  · Tags: ,

Taken from Why Use PLC: The softwiring advantage provided by programmable controllers is tremendous. In fact, it is one of the most important features of PLCs. Softwiring makes changes in the control system easy and cheap. If you want a device in a PLC system to behave differently or to control a different process element, all you have to do is change the control program. In a traditional system, making this type of change would involve physically changing the wiring between the devices, a costly and time-consuming endeavor.




You might also be interested in reading:
applied chemistry books for first year engineering students free download
« Prev